The blog of a dedicated radio amateur and electronics enthusiast

"Having fun on the air and in the workshop - communicating and creating"
Showing posts with label MF. Show all posts
Showing posts with label MF. Show all posts

28 May 2026

LF/MF dual-band transmit amplifier update

πŸ”²The original version of my LF/MF MOSFET Class-E πŸ—Όtransmitter power amplifier design was described on πŸ“…6 December 2015, with follow-ups on πŸ“…9 January 2016 & πŸ“…21 September 2017. It has been in regular use since then. However, several modifications have been made recently.
The ➰inductive reactance of the bias choke has been increased to the approximate optimal value of 30x MOSFET drain resistance, ( see Note below ), to improve the performance on the LF πŸ“2190m/∿136KHz band. So a second ⊚T200-26 core and a ⊚T157-52 core with 30 & 18 turn windings respectively have been added in series with the original ⊚T200-26 core ( 29 turn winding ); all are iron powder toroidal cores.
The ➿coil in the original LF band module could become quite hot. Two replacement modules have been made; one is completely new and uses Litz wire for the ➿coil, while the other is a redesign of the original still using 16 gauge enamelled copper wire (ecw), but changing capacitor values by "select-on-test". The coil-former for the 'ecw' version was 3-D printed from PETG filament, and is partially ribbed along its length. The DC blocking capacitor has to be a low-loss type  as the RF current through it can be considerable. Here, I have used several capacitors connected in parallel to share the current. The spacing between the ➿coil and ground-plane has been increased to reduce losses. Both designs for the LF band module will be tested in turn for comparison.
Internal view cover removed - note toroids & LF band module with ecw coil
Currently the output power is 172* watts on MF (πŸ“»πŸ“630m/∿472KHz band ), 282 watts on LF (πŸ“» πŸ“2190m/∿136KHz band Litz wire coil in band module ) and 302 watts on LF ( πŸ“»πŸ“2190m/∿136KHz band  16-gauge ecw coil in band module ) - see image below.πŸ”³
Oscilloscope display - (yellow) input voltage Vgs, (blue) output voltage Vo
Note: for Class E, Drain Load Resistance = (Supply Volts)πŸ ‰2 / 1.2 x Output Power
* Previously 210 watts with 2 x T200-26 bias choke ( 29 turn + 30 turn windings )

09 January 2024

3-D Printed Holders, Clips & Formers

πŸ”˜I've designed and printed a selection of parts some of which are intended for use in the transmitter power amplifier I am currently building for the 472KHz∿/630m wavelength radio πŸ“» band. So far I've made holders for some large foil capacitors, mounting clips for toroidal cores and coil formers ➿. Both PETG (grey) & PLA (blue or yellow) plastic filaments were used
Toroidal core clips, coil formers & capacitor holders
The toroidal core clip is for a T150-26 core which has an external diameter of 1.5". The coil fomers are ribbed for a close-spaced winding with 1.6mm diameter enameled copper wire. One side of the capacitor holder is open so that the value and voltage rating are visible. Where required, the parts can be panel-mounted using M2.5 nuts and bolts πŸ”©.
One benefit is that all dimensions and the style can be customised for a 'tailor-made' solution. I am no longer restricted to using PVC tube or pipe fixings for example, in only a few sizes bought from the shop. 

  

27 January 2018

Class C transmit amplifier for the 630m MF band

I continue to try different amplifiers in order to improve my station for weak signal digital modes, such as JT9 and WSPR, on the 475KHz, 630m band.
unboxed prototype amplifier with space left for antenna relay
The amplifier posted here is a medium power, and physically small, two IRF640N mosfet class C design. I designed the amplifier so that the 13degC/W heatsinks would provide adequate cooling for up to 50 watts output power when run from a 54Vdc power supply, while still retaining the compact size. With 2.5W drive power at the input, I measured 33W output power, ( gain 11.2dB ).  This was deliberate because at that power level, the optimum mosfet drain load is almost 50 Ohm; so I avoided the need for any output matching circuit. It will be interesting to see what I can achieve on digital modes now.
antenna change-over circuit added (lower-right)
Using it for the first time yesterday evening, my WSPR beacon transmission was received at a record distance 1655kms in France, and I was rewarded with a JT9 digital mode contact with Scotland at a similar distance.
 finished amplifier in home-made enclosure
 
3 February 2023
I received a request from a radio amateur in the USA ( Jeff, callsign WB8RJY ) for the circuit diagram, as he wanted to construct the amplifier. A few days later Jeff sent me several pictures of his completed amplifier, and a summary of his WSPR activity using the amplifier detailing some very long distance reception reports.
amplifier built by WB8RJY based on my design


 
 
 
 
 
 

02 November 2017

Phasing exciter for the MF 630m band

DDS interface dongle left, antenna c/o top, main board below
antenna change-over circuit removed to reveal main circuit board
So that I can join in the fun of using weak signal data modes such as JT9, JT65, FT8 and WSPR on the 475KHz 630m band I have built a phasing exciter for a low power single-sideband transmitter. Audio input signal is generated by pc data mode software and sound card. The rf signal source is a cheap AD9851 DDS module bought at an online auction site. Its frequency of operation is changed using the usb dongle and interface software obtained from www.spectecs.com. The rf phase shifter is a dual J-K flip-flop chip, af phase shifter comprises two quad opamps, and the mixer is a dual 1to4 mux/demux fet bus switch.
To give the project a smart appearance I chose a Hammond type 1455N1201BK box for it. Even before the prototype was finished, I couldn't resist the temptation of connecting it to my inverted 'L' antenna and trying it out. The exciter on its own produces only 1mW ( 1 milli watt, 0dBm ); but this was sufficient for my WSPR beacon signal on 474.2KHz to be received with SNR -23dB at a distance of 11kms by a monitoring station.
The prototype was completed with the addition of a class A rf driver amplifier to increase the output power to 100mW, and an automatic rf sensed antenna change-over switching circuit. Since then my signal has been received in Norway, distance 1071kms, Estonia, distance 816kms and Germany, distance 700kms, which surprised me as the antenna's directionality favours the east. Sadly there don't seem to be any foreign receiving stations in the east at the moment.

04 May 2016

Half-wave filter for the MF amplifier

Two T200-26 iron powder toroids are used
It's called a half-wave filter because it functions like a half-wavelength of transmission line, ( e.g., coax cable ), regarding the terminating impedances at the design frequency of 475.5KHz. Using lumped circuit elements is a much more practical proposition than 200m of cable. It also has a low-pass frequency response; theoretically 2nd harmonic 951KHz -27dB, and 3rd harmonic 1426.5KHz -47.8dB. This is a useful amount of extra attenuation. So I built it for use with my MF amplifier, ( posted 6 December 2015 ), to provide additional suppression of harmonics in the transmitted signal. It is connected externally in-line with the amplifier output.  

09 January 2016

Schmidt trigger input for the dual band amplifier

50% +DUT drive signal on the gate of one of the four MOSFETs
Schmidt trigger circuit installed
I have improved the amplifier efficiency by increasing the duty cycle ( +DUT ) of the drive signal on the MOSFETs' gates from 43% to 50% with the addition of a Schmidt trigger first stage. After experimenting with several CMOS NAND and inverter logic chips, ( i.e., CD4093BE, CD74HCT132E, SN74HC14N, SN74HCT14N ), which already have Schmidt trigger inputs, I found I could only obtain the 50% +DUT I wanted by making my own Schmidt trigger circuit using a quad 2-input NOR gate chip ( CD4001BCN or HEF4001BP ). I eventually decided to retain the older CD4001BCN in the circuit as the low pulse rate doesn't really justify using the newer HEF4001BP for this application. I built the circuit on a tiny piece of pad board and fitted it above the main driver circuit board. ( See also post dated 6 December 2015 ).

06 December 2015

Dual band transmitter power amplifier for the LF ( 2190m ) and MF ( 630m ) bands

home made enclosure 25 x 24.5 x 12cm


band module for the 2190m band is shown installed
I've recently finished building another amplifier for my transmitting setup for the 2190m/136KHz and 630m/475KHz bands. It is a switching amplifier design based on Class 'E' topology, using four IRF640N  MOSFETs in parallel. To allow operation on both bands I constructed the output tuning and matching circuit for each band as a removable module; changing the frequency band of operation just requires installing the appropriate module. I have also fitted a RF voltage sensed automatic antenna changeover circuit.
In use the amplifier runs only slightly warm. Each MOSFET is mounted on a separate 4.4degC/W heat-sink, two cooling fans are running and there is ample ventilation. So my work on the thermal aspects of the design was worth the effort. By using 4 MOSFETs in parallel there is very little heat to be dissipated anyway as their combined 'on-resistance' is extremely low. Amplifier efficiency is about 83%.
I was very pleased to get a reception report of my signal on the 630m band from Bantry, south-west Ireland, ( distance 2085 kms ), as well as reports from Greece and Spain.
My future plans are to paint the front panel of the enclosure, and make a hinged top cover.
I can provide the circuit diagram on request by email.