My low power LF radio signal is received in Germany

🔘 Almost 11 years 🗓 have passed since I last used my low-power transmitter power amplifier ( see 08.05.2013 ) based on the TDA2030 class AB audio 🔉 amplifier i.c. ( see 22.02.2013 ). Since then several data 💾 transmission modes, e.g., FST4W,  have become popular among radio amateurs who are active transmitting on the LF 2190m/136KHz 〰 ( longwave ) 📻 band. I also have high power transmitting equipment for that frequency band. However I wanted to conduct a simple test by transmitting a very low power beacon signal using FST4W to determine at what distance it might be received.

My setup for the test was the phasing exciter ( see 02.11.2017 ) as the signal source driving the low power amplifier. The antenna 🗼 was my usual one for the 2190m band; a 47m  long x 13.5m tall base and end-loaded inverted 'L' ( Ꞁ ) ;  see 19.02.2010 et al.  The transmit frequency ∿ was 136.13KHz, transmitter output power only 3.5 watts, ( similar to the power consumption of a small LED lamp 💡 ), and beacon transmission, consisting of my callsign, location and power level, sent at 5 minute intervals.

Equipment used for the low power test on 2190m band

I began sending beacon transmissions during the evening of  21.01.2024. Previously, during the tests on 8 May 2013, ( albeit using a different mode ), the reception distance had been only 17 kms. I was doubtful if anyone beyond that range would receive my signal. So I was very surprised, when, at 2120 utc 🕤, a reception report was posted 📮 on wspr rocks  ☁ that my beacon signal had been received 📶  near Chemnitz in Germany, at a distance of 582 kms. Incredible and amazing 😀 !

 

LF = Low Frequency.

135.7-137.8KHz ( 2190m band ) is the lowest frequency band allocated to radio amateurs.   

More details of my low power transmitting setup for longwave

Since the posts on 22nd February and 8th May, I have received requests to post more information on the setup I used for my low power test transmissions on the longwave 2190m band.

The circuit schematic and pcb artwork for the AF amplifier are shown above; click on the images to expand them. The original size of the artwork is 70 x 100mm. The pcb is single-sided; top component layer, bottom copper layer. Anyone wishing to copy my pcb design might need to modify the tracks connecting T1, depending on the actual transformer which is available and the windings used.

A +18V dc power supply can be used for greater output power. I didn't try this only because I don't have a convenient way of providing that voltage, and also the fan is a 12V unit.

My very low power transmissions on longwave

Last night I made successful radio test transmissions on 137.7KHz, 2190m band, using only 3.5W transmitter power. My signal was received, ( screen capture below ), at a distance of 17Km. The signal strength suggests that 2-way communication at this power level would be possible over a much longer distance. The vertical streaks are probably static crashes as a thunder storm was active in the vicinity.

My setup was my own-design PIC controlled DDS and the TDA2030 AF amplifier featured on 22 February. 

It is unfortunate that amateur radio activity on the 2190m band is so low, as it is possible to enjoy communicating on this band with a minimal setup, as I have just shown.  

Experimental low power amplifier for 2190m longwave

I salvaged some potentially useful parts from a faulty pc power supply, e.g. bridge rectifier, schottky diodes, heatsink, fan, chokes, transformers. The 12V-0-12V, 5V-0-5V output transformer typically operates near 40KHz. I thought of using it for the output matching transformer in a low power transmit amplifier for the 136KHz, 2190m longwave band.
My design is based on the very cheap, ( half a $ ), TDA2030 class AB audio amplifier ic, which has a bandwidth of 140KHz.
The circuit is experimental. I was curious to find out if such an amplifier would be useful for 136KHz, despite using some untypical, possibly 'unsuitable', components.

I built the amplifier on a home-made printed circuit board, 70 x 100mm. The ex-pc transformer, ( yellow & black ), is on the left. The TDA2030 is mounted on the ex-pc heatsink. ( Pcb artwork and the circuit schematic are available from me on request ).

Fitting the circuit board inside the old pc power supply box, ( cover not shown ), with its original 12V fan, and adding a LED, rf and dc connectors, completed the construction.

For testing, I powered the amplifier from a +13.6Vdc power supply and connected the input to my frequency synthesiser tuned to 137.8KHz. With the input attenuation set to minimum, and the output terminated in a 50 Ohm load, the measured voltage gain was 41.75dB. Output power was 3.5W.
I could now either connect the amplifier directly to my longwave antenna and make some very low power test transmissions, or use it as an intermediate amplifier stage in a much more powerful transmitter, yet to be built.